LG dryer repair in Los Angeles

10%

off labor

when you book online

Labor only. Parts are not discounted.

Tell us what broke

We'll call or text about this repair. Nothing else.

State registered and insured Same-day, 2-hour window Diagnostic credited

An LG dryer usually tells you something before we arrive, because its display throws a code for a blocked vent, missing voltage or a bad temperature reading. We repair electric and gas LG dryers all around LA, next to a washer or stacked above one. Most calls get a visit that same day, inside a two-hour arrival slot.

Parts on an LG dryer: Heater elements, thermal fuses, thermistors, roller kits and belts for LG dryers come through ordinary parts distributors, and they're priced like any other mass-market brand. That covers almost everything a dryer wears out. The one item that needs care is the main board. It's matched to one platform revision, so we identify it from the dryer in front of us and never from a model family name.

How the visit goes: Whatever the screen shows, or doesn't, sets the order of work. For a vent code we look at airflow before anything electrical. A cold drum on an electric unit starts at the terminal block, where we read both legs of the 240-volt supply, because the motor runs on one leg and the heater needs both. Only after the supply checks out does the back panel come off.

LG dryer repair in LA
$130–400
Diagnostic
$70. It comes off the bill when you approve the repair. If you decline, it is all you pay.
Parts
Heater element, thermal fuse, thermistor, drum roller kit and drive belt. Common ones ride on the van, the rest are ordered by model number.
Warranty
90-day parts & labor on the work we did.

You approve the flat number before anything is opened.

Common LG dryer problems

For every LG complaint here you'll see the likely culprit and the reading our tech takes first.

  1. The screen reads d80, d90 or d95. Flow Sense is saying 80 to 95 percent of the exhaust path is choked, so we begin with lint inside the cabinet and work out along the duct.
  2. The drum turns but the air never warms. For an electric LG the suspects are the heater element, the high-limit thermostat and the thermal fuse, each one metered with the power off.
  3. PS shows up on an electric LG. Its heater is short of a full 240 volts, so the breaker and the cord terminal get checked before anyone touches a part inside.
  4. tE1 or tE2 appears. The board has lost a sensible reading from the thermistor, and the fault can sit in the sensor itself or in the wiring running back to it.
  5. A thump or squeal follows the drum around. Flat-spotted drum rollers or a worn idler pulley make that sound, and the belt gets a look in the same teardown.

LG dryer lines we see in LA

LG sells these dryers in two heat versions, and the fuel decides most of the diagnosis. Electric models carry a heater element plus the PS code, which flags missing voltage at the supply rather than a failed part. Gas versions have no element at all. Heat there comes from an igniter working with a flame sensor and a safety coil, so the gas valve gets closed and the whole burner unit is removed together. Installation matters almost as much. An LG stacked on its washer inside a hall closet must come down and out into the room first, which adds time on either fuel.

Where to go next

Dryer repair on other brands

Dryer repair on every other brand we service.

Independent repair service. We are not affiliated with, authorized by or trained by LG. Brand and series names are the trademarks of their owners, used here to describe the equipment we work on. Manufacturer parts are sourced for each job rather than held as brand inventory.

Repair or replace an LG dryer

Inside about twelve years, an LG dryer with a heat fault or a noisy drum is a good candidate for repair, since the parts involved cost little and turn up fast. That changes if the drum has rusted through or the rear bearing has worn into the housing, and then a new dryer makes more sense. An element and fuse job on an electric dryer typically runs $180-$280, and a belt with a new idler lands in the same band. The dryer repair cost guide walks through the parts and the labor behind each end of the range.

LG dryer questions

My LG dryer shows d80. Is something broken?

Not inside the machine, as a rule. That code means the dryer's own airflow reading puts the exhaust at roughly 80 percent restricted, and d90 or d95 mean it's getting worse. It will still dry, slowly and hot. We clean the lint route through the cabinet, then follow the duct to where it leaves the house. A blockage beyond that point is work for a duct cleaner, and we'll say so.

Why won't my LG dryer heat when it shows PS?

Because the heater is short of power, which points at the house wiring before the dryer. A 240-volt circuit uses a double breaker, and one half can trip while the other keeps the drum turning and the display lit. A loose screw on the block where the cord connects does the same thing. We measure the supply before ordering anything.

What do tE1 and tE2 mean on an LG?

Both point at temperature sensing. The board reads the thermistor to know how hot the air is, and when that reading drops out or makes no sense, it posts one of these codes. We meter the thermistor and then the wires between it and the board. A failed sensor is an inexpensive fix, and chafed wiring gets repaired at the damaged spot.

Can you work on an LG dryer stacked on the washer?

Yes. In a closet the dryer gets lifted off the washer and moved into the room so we can reach the rear, then lifted back once the work is done. That extra handling is why stacked work runs higher than the same job on a side-by-side pair. Gas models also get their supply valve closed before the lift, and the vent run is looked over before restacking.

Book the LG dryer repair

Same-day visits across Los Angeles, common parts on the van, the rest ordered by model number, and a flat price you approve before the dryer is opened.

Call nowBook online